How Often to Replace a Flow Hood or FFU HEPA Filter – Midwest Grow Kits
Free shipping on orders over $99

*Free shipping excludes wholesale, bulk & commercial equipment

Our Fall Sale is Here! Save big on Your Next Project!

Growing help M–F 11am–5pm CST · 1-800-921-4717

How Often to Replace a Flow Hood or FFU HEPA Filter (Chart + 4 Tests)

By Michael Hawthorne  •  0 comments  •   11 minute read

"How often do I need to replace the HEPA filter?" is one of the most common questions we get about flow hoods and fan filter units, and it's one of the hardest to answer with a single number. We put together the guidance below from Bonsai Filtration's own data and from long conversations with the engineers at the factories that build our filters. Their answers don't all agree. Instead of picking one number and pretending it's a fact, this guide gives you a realistic planning number, explains why that number moves, and shows you four simple tests that tell you when your filter is actually done.

The short answer: plan on replacing the HEPA filter in a flow hood or FFU about every 24 months for typical hobby use. Expect 12–18 months in a busy lab running most of the day, and 6–12 months in a dusty, round-the-clock environment. Some manufacturers recommend replacing as often as every 12 months no matter how much the unit is used. Treat 24 months as a planning number, not an expiry date. An agar plate test and an airflow check are what actually tell you when to swap it.

  • ~24 monthsHobby planning number
  • 12–18 monthsBusy lab, 8–12 hrs/day
  • 6–12 monthsDusty, 24/7 use
  • 80–100 fpmTypical face velocity
  • 1–2 monthsClean or swap pre-filter

Why there's no single replacement number

A HEPA filter wears out in two different ways, and they run on different clocks.

Loading is the obvious one. Every hour the blower runs, the filter traps more dust, spores and skin flakes. As the media fills, it resists airflow more, face velocity drops, and eventually the air coming off the filter stops moving fast and evenly enough to sweep contaminants off your work. Loading tracks run hours and how dirty your room is, which is why the chart below gives hour ranges.

Aging is the one people forget. The glass-fiber media, the adhesive that holds the pleats, and the gasket that seals the filter to its housing all break down over time, even when the unit sits in a closet. A gasket that has gone hard or compressed can let unfiltered air leak around the edge of a filter that is otherwise nearly clean. Aging tracks the calendar, which is why some manufacturers tell customers to replace at 12 or 24 months whatever the run hours.

For most hobby growers, the calendar wins. Someone using a hood 10 hours a week puts about 1,040 hours on it in two years, well short of the 2,500–3,000 hours the filter could take on before loading becomes the problem. That is why the hour and month columns in the chart aren't direct conversions of each other. They are two separate limits, and whichever one you reach first is the one that counts.

HEPA filter replacement chart

HEPA filter replacement chart for FFUs and flow hoods: planning hours and calendar months by environment, from dusty 24/7 industrial use at 6–12 months to very light hobby use at 36–48 months
General planning estimates only. Hour ranges and calendar ranges are separate guidelines, not direct conversions.

On a phone, here are the same numbers as text:

Your environment Plan to replace Hour range
Dusty / industrial, 24/7 or near-continuous 6–12 months 4,000–5,000 hrs
Busy lab or small production, 8–12 hrs/day 12–18 months 5,000–6,000 hrs
Hobby, 3–10 hrs/week, newer home with modern HVAC ~24 months 2,500–3,000 hrs
Hobby, 3–10 hrs/week, older home with HVAC over 10 years old ~24 months 2,500–3,000 hrs
Very light use, 1–5 hrs/week, clean room 36–48 months 3,000–8,000+ hrs

How to read the chart

  • Find your row, then lean toward the short end if you're unsure. A failing filter costs you plates, grain and weeks of work. A filter swapped six months early costs you one filter.
  • The two hobby rows carry the same planning number on purpose. An older house with an older HVAC system usually has more dust in the air, but the fix is better pre-filter care and more frequent testing, not a different replacement date. If you're in an older home, run the agar plate test more often.
  • The very light use row is the one to treat with the most caution. At 1–5 hours a week, the filter will rarely load up, so aging and seal condition are what wear it out. A filter that has gone 36–48 months has to keep passing your tests to stay in service.
  • The pre-filter changes everything. The same HEPA filter will last noticeably longer behind a clean pre-filter than behind a neglected one. That is the single biggest lever you control.

Our recommendation: plan by the calendar, and replace based on your test results. Put a reminder in your calendar 24 months from the day you install a filter. Until then, keep using it as long as it passes the agar plate test and holds its airflow. If it fails either one, replace it, even if it's only a year old.

4 ways to tell if your HEPA filter is still working

1. The agar plate test (the most useful test for growers)

This tests the thing you actually care about: whether the air at your work surface is clean enough for sterile work. It is the best practical test a hobbyist can run.

  1. Get sterile agar plates. MEA, PDA or any similar general-purpose agar works. Pre-poured sterile plates save time and remove one variable.
  2. Run the hood or FFU for 10–15 minutes so the airflow settles into its normal pattern.
  3. Open 2–4 plates in your working zone, roughly in the center of the filter face where your hands normally are, for 1–5 minutes. Five minutes is the stricter version.
  4. Open one control plate out in the room for the same amount of time, away from the airflow.
  5. Close, seal, label and incubate. Wrap with Parafilm or tape, label which plates were under the hood, and incubate at room temperature or about 70–75°F (21–24°C) for 3–7 days.
  6. Count the colonies. Compare the hood plates with the control.
What you see What it means
0–1 colonies on the hood plates, growth on the room control Filter and airflow are doing their job.
Several colonies on the hood plates, or consistent growth from test to test A problem: a loaded or clogged filter, a leak around the seal, turbulence, or a technique issue. Re-check the pre-filter and your setup, then retest.
As much growth on the hood plates as on the control The filter is not protecting your work area. Replace it, or find the leak, before doing more sterile work.

Run this every few months, and any time your contamination rate starts climbing.

2. The flame or lighter test (a quick check of airflow)

Hold a long-stem lighter or a lit incense stick in the airstream 6–10 inches from the filter face, and move it across the face, covering the center and the edges.

  • Good flow: the flame bends steadily at roughly 45 degrees and stays fairly stable, with little flickering.
  • Too weak: the flame stands nearly straight up.
  • Too fast or turbulent: the flame bends close to 90 degrees and won't settle.
  • Dead zones or turbulence: the flame flickers a lot, or behaves differently at different points across the face.

This doesn't prove the filter is still catching particles, but it shows in seconds whether airflow speed and evenness are still where they should be. Many growers use it as a quick check before every session. Keep the flame well away from the filter media itself.

3. Measure face velocity with an inexpensive anemometer

Face velocity for most laminar flow hoods used in mycology is typically 80–100 feet per minute (about 0.4–0.5 m/s). A basic digital anemometer costs around $20–50 and turns the airflow check into a number you can track.

  1. Record a baseline when the filter is new. Measure at several points across the face, in the center and near each edge, on the speed setting you normally use.
  2. Recheck every few months with a clean pre-filter. Always clean or replace the pre-filter first, so you're measuring the HEPA filter and not a dirty pre-filter.
  3. Watch for a real drop. Readings consistently below about 70–80 fpm, or more than 15–20% below your own baseline, usually mean the HEPA filter is loaded and due for replacement.

Your own baseline matters more than the textbook range. FFUs with adjustable fan speeds will read differently on each setting, so always compare like with like.

4. Pre-filter condition and everyday warning signs

  • Pre-filter: inspect it regularly, and clean or replace it when it looks gray or dirty, or when the airflow feels weaker. Depending on how dusty your space is, that's usually every 1–2 months. Bonsai FFUs use a washable magnetic pre-filter that rinses clean. Bonsai's XL and Commercial flow hoods take a standard HVAC-style pre-filter on the intake that you swap out.
  • Airflow feel and noise: if the airflow is noticeably weaker or the fan sounds strained or louder than usual even with a clean pre-filter, the HEPA filter is loading up.
  • Visual check: look for tears, punctures, crushed pleats, heavy discoloration on the media, or a gasket that has hardened, cracked or pulled away. Any physical damage means replace it now.
  • Your results: if plates or grain that used to run clean start contaminating more often, that is one of the clearest real-world signs, as long as your technique hasn't changed.

Never wash, vacuum, blow out or touch the HEPA filter media. The media is a fragile mat of fine glass fibers, and any contact can tear it or open channels that let unfiltered air through. Only the pre-filter is meant to be cleaned.

How to make a HEPA filter last longer

  • Stay on top of the pre-filter. It catches the larger dust that would otherwise load the HEPA filter, so this is the biggest single factor in filter life.
  • Keep the room clean. Vacuum and wipe down your workspace before sessions. Avoid running the unit in a room with fresh sawdust, drywall work, pets or open bags of substrate.
  • Don't run it when you don't need it. Fewer run hours means less loading. Run it 10–15 minutes before work so the airflow settles, then shut it off when you're done.
  • Protect the filter face. Keep tools, spray bottles and gloved hands from hitting the media, and never spray alcohol directly onto the filter.
  • Write down the install date. Put a label on the housing with the date and your baseline airspeed reading. Six months from now, you won't remember either.

Replacement filters for Bonsai and Myco Labs units

Every replacement filter below is H14 99.995% HEPA and made to fit its unit exactly.

Your unit Replacement filter
Bonsai 12" laminar flow hood HEPAFLOW-12 replacement filter
Bonsai XL 24" × 18" flow hood XL 24" × 18" replacement filter
Bonsai Commercial 48" × 24" flow hood 2' × 4' commercial hood filter
Bonsai 2' × 2' FFU 2' × 2' FFU filter
Bonsai 3' × 2' FFU 3' × 2' FFU filter
Bonsai 4' × 2' FFU 2' × 4' FFU filter
Myco Labs 23" × 23" FFU 23" × 23" FFU filter
Myco Labs 2' × 4' FFU Myco Labs 2' × 4' FFU filter

Keep a spare on the shelfA filter that fails a plate test in the middle of a run of agar work costs you more than the filter. Having a spare means you can swap it the same day instead of pausing your work while one ships. If you're still choosing equipment, our guide to laminar flow hoods vs. FFUs walks through which one fits your space, and the full range is in flow hoods & clean room.


Frequently asked questions

How often should I replace the HEPA filter in my flow hood or FFU?

For typical hobby use, plan on about every 24 months. Busy labs running 8–12 hours a day usually need a new filter every 12–18 months, and dusty, round-the-clock environments every 6–12 months. Some manufacturers recommend replacing as often as every 12 months no matter how much the unit is used, because the media and seals age over time. Treat these as planning numbers, and use an agar plate test and an airflow check to decide when your filter is actually done.

How many hours does a HEPA filter last?

As general planning ranges, about 2,500–3,000 hours for typical hobby use, 5,000–6,000 hours in a well-kept commercial lab, and 4,000–5,000 hours in dusty, continuous industrial use. Hours and months are separate limits, not conversions of each other. Most hobby growers reach the calendar limit long before they run out of hours.

Why do manufacturers give such different replacement times?

Because a HEPA filter wears out in two ways. Loading from trapped dust tracks run hours and how clean the room is. Aging of the media, adhesive and gasket seals tracks the calendar, even if the unit is rarely used. Manufacturers that focus on loading quote hours; manufacturers that focus on aging recommend a fixed 12- or 24-month replacement. Both are valid, so we suggest planning by the calendar and replacing based on test results.

My filter is over two years old but my plates still come out clean. Do I have to replace it?

Not necessarily. With very light use in a clean room, some filters stay in service for 36–48 months. The 24-month figure is a planning number, not a hard limit. Keep running agar plate tests every few months, check the gasket for hardening or gaps, and replace the filter as soon as a test shows a problem.

How do I test my flow hood with agar plates?

Run the unit for 10–15 minutes, then open 2–4 sterile agar plates in your working zone for 1–5 minutes, with one control plate open in the room for the same time. Seal, label and incubate at about 70–75°F for 3–7 days. Zero or one colony on the hood plates, with growth on the control, means the filter and airflow are working. Several colonies on the hood plates means a loaded filter, a leak, turbulence or a technique problem.

What face velocity should a flow hood have?

Most laminar flow hoods used in mycology run around 80–100 feet per minute at the filter face, about 0.4–0.5 m/s. Record a baseline with an anemometer when the filter is new. If readings stay below about 70–80 fpm, or more than 15–20% below your baseline, after cleaning the pre-filter, the HEPA filter is likely loaded and due for replacement.

Can I clean or vacuum a HEPA filter to make it last longer?

No. Never wash, vacuum, blow out or touch the HEPA media. It is a fragile mat of fine glass fibers, and contact can tear it or open channels that let unfiltered air through. Clean or replace the pre-filter instead, usually every 1–2 months. That is the most effective way to extend HEPA filter life.

How often should I clean the pre-filter?

Every 1–2 months for most home setups, and sooner in dusty spaces or whenever it looks gray or airflow feels weaker. Bonsai FFUs use a washable magnetic pre-filter that rinses clean. Bonsai's XL and Commercial flow hoods take a standard HVAC-style intake pre-filter that you swap out.

Previous Next

Leave a comment

Please note: comments must be approved before they are published.